How to Verify a Salt Spray Report: A Checklist for Coated Steel Buyers

Nov 16, 2026

Leave a message

info-1828-1028

Salt spray reports are easy to misread. A page arrives with a duration, a standard number and a verdict, and the duration is treated as a quality score. In our own review work, that shortcut runs in both directions: a sound coating gets discounted because the test panel did not represent the product, and a thin coating gets accepted because the panel was small, edge-sealed and never scribed.

 

What follows is the sequence our technical team works through when two reports do not agree. It takes about ten minutes per document.

The table below is the short form of that sequence.

 

Table 1. Salt spray report checklist

What to check

What a complete answer contains

Standard and variant

ASTM B117 or ISO 9227, with the variant and edition year, and the operating values: 5% NaCl, pH 6.5 to 7.2, 35 ± 2 °C, 1 to 2 mL per 80 cm² per hour, panel inclination.

Specimen

Substrate, coating designation, measured coating mass or dry film thickness, panel size, edge treatment, flat or formed, scribed or unscribed.

Endpoint and scale

The event that ended the test, the rating scale applied, and the inspection intervals.

Photographs

Whole panel before and after exposure, legible at the failure site, matched to the panel identifiers.

Data layout

Results per panel rather than a lot average, with the location of first failure noted.

Provenance

Report number, date, laboratory, operator, chamber calibration; accreditation body and scope where accreditation is claimed.

The duration is the last item on the page

 

Salt spray testing is a comparative method. It holds a specimen in a fixed environment and records how long a coating resists a defined failure. It does not measure service life, and no figure from it converts into years.

 

Two laboratories can follow the same standard and still land hundreds of hours apart, because coating mass, edge condition, panel inclination and chamber loading all move the result. Read the report in this order: method, specimen, endpoint, photographs, and only then the hour count.

 

Check the variant, not just the standard number

 

ASTM B117 and ISO 9227 are quoted as though they were the same test. They are not interchangeable entries. B117 is a practice for operating a salt fog chamber: it fixes the apparatus, the salt solution and the exposure regime. ISO 9227 itself covers three variants: neutral salt spray, acetic acid salt spray and copper-accelerated salt spray, each with its own solution and pH range. A report that names the standard but not the variant cannot be reconstructed.

 

Next, look for the operating values. Neutral salt spray runs on a 5% sodium chloride solution at pH 6.5 to 7.2, a chamber temperature of 35 ± 2 °C and a fog collection rate of 1 to 2 mL per hour per 80 cm². Panel inclination is specified as well, and it changes the result: condensate drains differently from a near-vertical panel and one leaned further back. Where the standard is cited but none of these figures appear, the page was probably assembled from a template. Ask for the chamber record.

 

The specimen description is where comparison breaks

 

"Galvanized steel" is a family, not a specification. A Z120 coating and a Z275 coating will not reach red rust at the same time in the same chamber, and a Galvalume panel of equal coating mass behaves differently, because the aluminium in the 55% Al-Zn layer changes how corrosion spreads away from a cut edge.

 

A complete entry gives the substrate, the coating designation, the measured coating mass in g/m² or the dry film thickness in µm, the panel dimensions, the edge preparation, and whether the panel was tested flat or formed. Edge preparation carries more weight than most buyers expect: a sheared edge leaves bare steel exposed and rusts well before the coated face, while a taped edge delays that failure and flatters the number.

 

For prepainted coil, one further item decides what the test actually measures: the scribe. Without one, you test the barrier properties of the paint system; with one, you test how far corrosion travels along the cut, which is the behaviour that matters at a cut edge on a roof.

info-776-776
info-420-420

Fix the endpoint before you read the result

 

"Passed 500 hours" is a verdict without a measurement. The usable result is the time at which a specified event was first observed, assessed on a published scale. For zinc and zinc-aluminium coatings, keep white rust and red rust apart. White rust is the corrosion product of the coating itself and shows that the zinc is still working. Red rust means the steel beneath is corroding, and that is where protection has ended. A report that records only "no corrosion" at 500 hours has usually not looked for white rust.

 

On prepainted panels the observations are blistering, rusting, cracking and creep measured in millimetres from the scribe. The rating scales exist so that these can be compared across laboratories: ISO 10289 for coated specimens after corrosion testing, ASTM D1654 for painted panels carrying a scribe, and the ISO 4628 series for the appearance defects. A single inspection at the end of the run is weak evidence, since the first red rust may have appeared several hundred hours earlier. Intermediate assessments narrow that window.

 

Photographs, per-panel data and provenance

 

Photographs belong in the evidence, not in an appendix. They should cover the whole panel before and after exposure, at a magnification that lets a reader separate white from red corrosion, and they should carry the panel identifier used in the data table. Give results per panel rather than as a lot average: three panels averaged into one figure hide the worst panel, and the worst panel predicts how a coil behaves at a cut edge.

 

Provenance is the other half: report number, date, laboratory, operator and the calibration status of the chamber. Where the laboratory is accredited to ISO/IEC 17025 for salt spray testing, the report normally shows the mark and the scope under which the test was run. Accreditation confirms that the method was executed competently. It does not confirm that the panel represented your coil, and that gap matters when an accredited report is offered as proof of coating quality.

 

If a continuous test is the only evidence on offer, ask for cyclic data as well. Wet and dry cycles, as set out in ISO 14993, ASTM G85 or VDA 621-415, follow field behaviour more closely. Outdoor exposure reported to ISO 8565, with the site classified under ISO 9223, is the better reference still.

 

What a salt spray report cannot settle

 

No salt spray result converts into years of service. The test accelerates one mechanism under one fixed set of conditions. It does not reproduce ultraviolet exposure, thermal cycling, run-off from a roof, chloride deposition from sea air, or the damage a coil takes during roll forming, profiling and fixing.

 

Use the report to establish comparability between suppliers, then judge the coating system against the environment the project will actually face: corrosivity category, position on the structure, edge and fastener details, and the maintenance interval the owner is prepared to accept. ISO 12944 provides the framework for that judgement at system level. The salt spray figure is one input to it.

 

Putting the checklist into a purchasing cycle

 

Keep the list to one page and attach it to the first request for a test report. Ask each supplier for the same method and rating scale, and treat reports from different standards as separate datasets rather than competing figures. File the completed page with the material qualification record, and read new reports against the earlier ones for the same product line. A jump in reported hours with no change in coating mass or film thickness deserves a question.

 

Our technical resources page carries a report template with these fields, and each product page lists the coating mass, thickness and test basis we certify for galvanized, Galvalume and prepainted coil. If two reports do not line up, send both to our technical team and we will tell you where they diverge.

 

Send Inquiry